WengYang Industriegebiet Yueqing Wenzhou 325000
Arbeitszeiten
Montag bis Freitag: 7AM - 7PM
Am Wochenende: 10AM - 5PM
3-polige vs. 4-polige ATS: Wann sollte ein Netzumschalter den Neutralleiter schalten?
Short answer: A three-pole automatic transfer switch (ATS) transfers the three phase conductors while the load neutral remains solidly connected. A four-pole ATS also transfers the neutral. The correct choice depends on the system’s neutral-to-earth bonding, whether the generator is a separately derived source, protection design, and the applicable local rules. A four-wire load does not automatically require a switched neutral.
Why the neutral decision matters
When utility power fails, an ATS transfers a load to an alternate source such as a generator. The neutral arrangement determines how return current and ground-fault current flow in each operating mode. An incorrect arrangement can create parallel neutral paths or undermine ground-fault protection. The decision must therefore be made from a complete single-line diagram, not from pole count alone.
What a 3-pole ATS does
A three-pole device switches L1, L2 and L3. In a solid-neutral arrangement, the utility neutral, generator neutral and load neutral remain connected through the transfer equipment. This can suit a generator installation that uses the service neutral-to-earth bond and is nicht configured as a separately derived system. The generator bonding arrangement must be checked; a second neutral-to-earth bond can create an unwanted parallel path.
What a 4-pole ATS does
A four-pole device switches L1, L2, L3 and N. Its neutral pole connects the load neutral to the selected source. This arrangement is commonly considered when the alternate source has its own neutral-to-earth bond and is designed as a separately derived system. The neutral contact sequence and grounding design are critical; “four poles” alone does not describe every neutral switching mechanism. Protective earth must remain continuous and must never be used as the switched neutral.
Quick comparison
| Designfrage | 3-pole / solid neutral | 4-pole / switched neutral |
|---|---|---|
| Transferred conductors | Three phases | Three phases and neutral |
| Load neutral | Remains connected to both source neutrals | Connects to selected source neutral |
| Typical design context | Alternate source is not separately derived | Alternate source is separately derived |
| Key verification | Bonding and parallel neutral paths | Neutral contact sequence, bonding and protection coordination |
These are design patterns, not a substitute for local electrical code or a site-specific engineering review.
Selection checklist for a generator ATS
- Draw the utility, generator, ATS, load neutral and protective-earth conductors on one single-line diagram.
- Identify every neutral-to-earth bond in both operating modes.
- Confirm whether the generator is intended to be separately derived under the applicable installation rules.
- Review ground-fault and residual-current protection with both sources energized independently.
- Check the ATS manufacturer’s neutral pole arrangement, contact sequence, ratings and wiring diagram.
- Have the design checked against local code by a qualified electrical professional before installation.
How this applies to Kuangya transfer switches
Kuangyas KGQ2 automatic changeover switch is offered in 3P and 4P variants. Choose the pole configuration only after the system grounding design is settled; then confirm the exact model’s wiring diagram, ratings and neutral contact behavior with the supplier. You can compare the broader Kuangya ATS range oder send your single-line diagram for a product selection discussion.
Häufig gestellte Fragen
Does every three-phase, four-wire system need a 4-pole ATS?
No. The need to switch the neutral is determined by the source bonding and protection design. A four-wire load can be served through an ATS with a solid neutral where that arrangement is appropriate.
Can I switch the protective-earth conductor?
No. The protective-earth continuity is part of the safety system. A neutral switching pole is not a protective-earth pole.
Is a generator always a separately derived system?
No. That classification depends on how its neutral is connected through the transfer equipment and how the system is bonded. Check the entire installation.
Technical references
- Schneider Electric / ASCO: transfer-switch neutral configurations explains solid, switched and overlapping neutral arrangements.
- Schneider Electric / ASCO: Neutral Configurations in Transfer Switches discusses how a separately derived ground affects selection.
- Schneider Electric: when to separately ground a backup generator gives the grounding context.
Engineering note: This article is a selection guide, not an installation instruction. Follow the approved design, the exact device documentation and local electrical requirements.
