発電機ATS(自動切替スイッチ)切替時にRCCBまたはRCBOがトリップする場合の確認事項

ATSが発電機の電源に切り替わるとき、なぜRCCBまたはRCBOがトリップするのか?中性線の配置、接地および漏れ経路を比較し、その後、メーカーのガイダンスに基づいた安全な診断チェックリストに従ってください。

Kuangya two-pole RCCB product used to illustrate residual-current protection in generator transfer systems
Illustrative Kuangya RCCB. A product image does not establish suitability for a particular generator or transfer-switch installation.

クイックアンサー: If an RCCB or RCBO trips when an automatic transfer switch (ATS) moves a load from utility power to a generator, do not simply fit a less sensitive device. The electrician should trace both source paths and check neutral switching, neutral-to-earth bonding, all conductors passing through the residual-current sensor, connected equipment leakage and the device’s exact operating conditions. A trip can indicate a real fault or an unintended return path; the symptom alone cannot identify which.

Why source transfer can change residual current

An RCD compares current flowing through all active conductors of the protected circuit, including the neutral where present. If some current returns by another path, the imbalance can cause a trip. Schneider Electric’s RCD explanation describes this sensing principle. During transfer, the source, neutral connection and earthing arrangement may change. Generator start-up can also bring loads back online together; a faulty appliance or cumulative leakage may appear at that moment. These are possibilities to test, not a diagnosis from the timing alone.

Compare the two transfer arrangements

ArrangementWhat changesReview before selecting the RCD
Solid neutral ATSThe load neutral remains connected to the normal-source neutral while phase conductors transfer.Where is the intended neutral-to-earth bond? Is there another bond at the generator that creates parallel return paths?
Switched neutral ATSThe neutral is transferred with the phase conductors.How is the generator source bonded when selected? Are earthing and protective conductors continuous as required?

Neither option is automatically correct for every installation. The arrangement depends on the system earthing design, generator configuration, national rules and the transfer equipment. Schneider Electric’s generator grounding example explains how a solid neutral and a switched neutral lead to different source-grounding schemes. Its ASCO neutral-switching white paper documents the design choice. These are third-party application examples, not proof that one Kuangya model is approved for a specific ATS.

A practical fault-finding sequence

  1. Record the event. Does the device trip at transfer, on generator start, when a particular load reconnects, or only on return to utility? Note the exact RCCB/RCBO model and any fault indicator.
  2. Draw both source states. Mark ATS poles, generator and utility neutrals, neutral-to-earth bonds, protective conductors, RCD position and every downstream neutral.
  3. Check conductor routing. Every active conductor of a protected circuit must pass through the same residual-current sensing device. A borrowed neutral or a neutral connected to another circuit can create an imbalance.
  4. Inspect the source bonding design. A second, unintended neutral-to-earth link can provide a parallel return path. A missing appropriate link in an islanded system can also undermine fault protection. Do not add or remove a bond by trial and error.
  5. Isolate the load cause. A qualified person can test leakage and insulation in accordance with equipment instructions, then reconnect circuits in a controlled sequence. Inspect outdoor equipment and motor or electronic loads where the trip follows a specific load.
  6. Verify protection on both sources. Commission the transfer arrangement and test fault protection with suitable instruments and the manufacturer’s procedure, not only with the RCD TEST button.

Victron Energy’s Wiring Unlimited guidance explains why a neutral-to-earth link and the source mode matter for RCD operation in generator or inverter systems. It also warns that a TEST button check is not a test of the complete installation. The exact bonding point and method must follow local wiring rules and the actual equipment design.

RCCB, RCBO or upstream ground-fault protection?

アン RCCB provides residual-current protection but needs appropriate overcurrent protection. An アールシーボ combines residual-current and overcurrent functions in one device. Neither fixes a neutral-bonding error. Larger systems may also use separate ground-fault sensing and protective coordination; do not treat a small final-circuit RCCB as interchangeable with that scheme. The RCCB versus RCBO guide covers the functional difference, while our TEST-button guide explains the limits of that check.

Documented scenario, not a fabricated customer case

Schneider Electric describes real transfer-switch design configurations with either a solid or switched neutral and relates them to generator grounding and ground-fault sensing. Victron documents the source-bonding issue in generator and inverter installations. Together, these published engineering examples show why a trip after transfer calls for a system review. We do not have a verified Kuangya customer installation, measured leakage record or before-and-after repair report for this exact symptom, so no such result is claimed here.

What to include in a product enquiry

Send the single-line diagram, supply and generator voltage, earthing arrangement, ATS pole count and neutral configuration, generator bonding instructions, circuit loads, prospective fault current, required residual-current protection and the location of each proposed RCCB/RCBO. Ask for the exact product datasheet, wiring instructions and market-specific certification evidence. The SPD placement guide for generator and ATS systems covers the separate surge-protection question.

よくある質問

Should I replace a 30 mA RCD with a 100 mA device to stop tripping?

Do not change sensitivity as a shortcut. Protection requirements depend on circuit purpose and local rules. First locate the fault or unintended current path; have a qualified designer assess any protection change.

Does a four-pole ATS always solve the problem?

No. A switched neutral may be appropriate for a separately derived arrangement, but it must be coordinated with the generator bond and the whole earthing scheme. An unrelated appliance fault or shared downstream neutral can still trip an RCD.

Can the TEST button prove the generator mode is safe?

No. It checks part of the device’s mechanism under the specified conditions. It does not prove the complete fault path, earthing arrangement, operating time or protection of every circuit.

Editorial responsibility: elaine, Kuangya Electric. This article summarizes the cited manufacturer guidance for engineering review. It is not a site-specific wiring instruction; isolation, testing and correction of mains or generator circuits belong to qualified electrical personnel.

エレーン
エレーン

Kuangyaのマーケティング責任者として、電気保護および配電ソリューションのグローバルプロモーションに注力:コア分野:太陽光発電、エネルギー貯蔵、産業用電力市場におけるブランド構築。プロフェッショナル製品業務用製品:ヒューズ、サージ保護装置(SPD)、小型サーキットブレーカー(MCB)、トランスファースイッチ。価値提案:安全性、信頼性、革新性」を基軸に、世界の再生可能エネルギー市場に貢献します。インテリジェント配電技術の進歩を共同で推進するため、ぜひご連絡ください。.

記事本文: 193