{"id":4853,"date":"2026-10-28T11:39:40","date_gmt":"2026-10-28T03:39:40","guid":{"rendered":"https:\/\/cnkuangya.com\/?p=4853"},"modified":"2026-10-28T11:39:46","modified_gmt":"2026-10-28T03:39:46","slug":"heat-pump-rcd-type-a-f-b","status":"publish","type":"post","link":"https:\/\/cnkuangya.com\/fr\/blog\/heat-pump-rcd-type-a-f-b\/","title":{"rendered":"Quel interrupteur diff\u00e9rentiel pour une pompe \u00e0 chaleur ? Type A vs Type F vs Type B"},"content":{"rendered":"

R\u00e9ponse rapide :<\/strong> There is no single RCD type for every heat pump. Type A may be specified for some units and jurisdictions; Type F can be appropriate for certain single-phase inverter-driven heat pumps that may produce composite residual currents; and Type B may be needed where smooth DC residual current can occur. Start with the exact heat-pump installation manual and local electrical rules, then match the RCD to the expected fault-current waveform.<\/p>\n

The words heat pump<\/em> do not tell you whether the compressor drive is single-phase or three-phase, whether DC fault monitoring is built in, or which protective device the manufacturer tested. Those details decide the selection.<\/p>\n

Why Does RCD Type Matter for a Heat Pump?<\/h2>\n

A residual-current device detects current leaving the intended circuit path and disconnects under specified conditions. An inverter-driven heat pump may create residual-current waveforms different from a simple resistive heater. Selecting the wrong detection type can leave a fault waveform outside the device’s intended capability; choosing a different type without checking the equipment can also cause unnecessary cost or unwanted trips.<\/p>\n

IEC 62423<\/a> defines additional requirements and tests for Type F and Type B RCDs. Schneider Electric’s technical paper on RCD types<\/a> uses a single-phase heat pump with a variable-speed drive as an example of an application that may produce composite residual current.<\/p>\n

Type A vs Type F vs Type B: What Changes?<\/h2>\n\n\n\n\n\n\n\n
Type de RCD<\/th>\nRelevant detection capability<\/th>\nHeat-pump selection question<\/th>\n<\/tr>\n<\/thead>\n
Type A<\/td>\nSinusoidal AC and pulsating DC residual current<\/td>\nDoes the equipment manual permit Type A for this exact circuit and installation?<\/td>\n<\/tr>\n
Type F<\/td>\nType A capability plus specified composite residual currents associated with single-phase frequency converters<\/td>\nIs the heat pump a suitable single-phase inverter application, and does the manual call for Type F?<\/td>\n<\/tr>\n
Type B<\/td>\nIncludes smooth DC residual-current detection within its specified range<\/td>\nCan the equipment produce smooth DC fault current, or does its manual require Type B?<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

Type F is pas<\/strong> a substitute for Type B when smooth DC fault-current detection is required. Type B is also not an automatic upgrade for every heat pump. The connected equipment and applicable rules determine the correct device.<\/p>\n

Single-Phase Inverter Heat Pumps: When Type F Enters the Discussion<\/h2>\n

A single-phase frequency converter can produce composite residual currents. IEC 62423 describes Type F devices for installations where frequency inverters are supplied between phase and neutral (or an earthed middle conductor). This makes Type F a relevant option to investigate for some single-phase inverter heat pumps.<\/p>\n

That does not mean every single-phase heat pump requires Type F. For example, New South Wales government guidance for heat-pump hot-water installations<\/a> specifies Type A under its stated local rules. The equipment manufacturer and the installation jurisdiction must be checked together.<\/p>\n

Three-Phase Units and Smooth DC Risk<\/h2>\n

Some three-phase drive arrangements may create residual-current components that a Type A or Type F device is not intended to detect. The drive topology, fault path and any integrated monitoring matter more than a simple \u201cthree-phase equals Type B\u201d slogan. If the heat-pump manual calls for Type B, do not substitute another type solely to reduce cost.<\/p>\n

Schneider Electric’s RCD selection guide for DC earth leakage<\/a> explains why DC components can affect RCD selection and upstream coordination. A qualified designer should also check whether an upstream RCD could be exposed to DC residual current from the heat-pump circuit.<\/p>\n

RCCB or RCBO for a Heat Pump?<\/h2>\n

RCD type<\/em> describes residual-current detection. It does not answer whether the circuit should use an RCCB with a separate overcurrent protective device or an RCBO combining residual-current and overcurrent protection. That choice depends on circuit design, breaker rating, discrimination and the available panel space. See our RCBO type and rating guide<\/a> et RCBO product range<\/a>.<\/p>\n

Do not use the compressor’s rated power alone to choose the RCD’s current rating, residual operating current or trip curve. Check the manufacturer’s electrical data, starting behavior, conductor protection, and applicable installation standard.<\/p>\n

Seven Checks Before Ordering<\/h2>\n
    \n
  1. Exact heat-pump model:<\/strong> obtain the current installation manual, not only a sales brochure.<\/li>\n
  2. Supply arrangement:<\/strong> confirm voltage, phases, neutral and earthing system.<\/li>\n
  3. Required RCD type:<\/strong> look for an explicit Type A, F or B instruction and any integrated DC monitoring.<\/li>\n
  4. Residual-current sensitivity:<\/strong> follow local requirements and the equipment manufacturer’s instructions.<\/li>\n
  5. Normal leakage:<\/strong> evaluate the total leakage of the heat pump and other loads on the same RCD.<\/li>\n
  6. Overcurrent protection:<\/strong> coordinate the RCCB\/RCBO with the conductor and prospective fault current.<\/li>\n
  7. Upstream coordination:<\/strong> check the effect of DC components and the selectivity of devices in series.<\/li>\n<\/ol>\n

    For a wider discussion of RCD types and selectivity, read our residential RCD coordination guide<\/a>. When requesting a quotation, send the model manual, supply details, required poles, desired device type, current rating, residual-current sensitivity and destination-market standard to KUANGYA<\/a>. This lets the supplier check the exact model rather than suggesting a device from the phrase \u201cheat pump\u201d alone.<\/p>\n

    FAQ<\/h2>\n

    Can I use a Type A RCD for a heat pump?<\/h3>\n

    Possibly. Some equipment instructions and local rules specify Type A. Confirm the exact model, residual-current characteristics and jurisdiction before selection.<\/p>\n

    Is Type F always better than Type A?<\/h3>\n

    No. Type F adds specified composite-current detection for relevant single-phase inverter applications, but the heat pump’s instructions and local rules decide whether it is needed and permitted.<\/p>\n

    Does Type F detect smooth DC faults like Type B?<\/h3>\n

    No. Type F’s ability to tolerate a limited superimposed smooth DC component is not the same as Type B smooth DC residual-current detection.<\/p>\n

    Will a different RCD type fix repeated nuisance tripping?<\/h3>\n

    Not necessarily. First check wiring, actual leakage, moisture, equipment faults, shared neutrals and the manufacturer’s protective-device requirements. Changing type without diagnosing the cause may leave the problem unresolved.<\/p>","protected":false},"excerpt":{"rendered":"

    Quel type de DDR est n\u00e9cessaire pour une pompe \u00e0 chaleur ? Comparez les types A, F et B pour les unit\u00e9s \u00e0 variateur de vitesse, puis v\u00e9rifiez le manuel, le courant de d\u00e9faut et les r\u00e9glementations locales avant de commander.<\/p>","protected":false},"author":4,"featured_media":4860,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[35,47],"tags":[],"class_list":["post-4853","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-blog","category-rcd-leakage-protection"],"blocksy_meta":[],"_links":{"self":[{"href":"https:\/\/cnkuangya.com\/fr\/wp-json\/wp\/v2\/posts\/4853","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/cnkuangya.com\/fr\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/cnkuangya.com\/fr\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/cnkuangya.com\/fr\/wp-json\/wp\/v2\/users\/4"}],"replies":[{"embeddable":true,"href":"https:\/\/cnkuangya.com\/fr\/wp-json\/wp\/v2\/comments?post=4853"}],"version-history":[{"count":2,"href":"https:\/\/cnkuangya.com\/fr\/wp-json\/wp\/v2\/posts\/4853\/revisions"}],"predecessor-version":[{"id":4862,"href":"https:\/\/cnkuangya.com\/fr\/wp-json\/wp\/v2\/posts\/4853\/revisions\/4862"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/cnkuangya.com\/fr\/wp-json\/wp\/v2\/media\/4860"}],"wp:attachment":[{"href":"https:\/\/cnkuangya.com\/fr\/wp-json\/wp\/v2\/media?parent=4853"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/cnkuangya.com\/fr\/wp-json\/wp\/v2\/categories?post=4853"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/cnkuangya.com\/fr\/wp-json\/wp\/v2\/tags?post=4853"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}